DRV8838 - single-channel motor controller 11V/1,7A - Pololu 2990

Бестселлер
47398074
943 ₽

Мы сотрудничаем с поставщиками электрики Pololu и предлагаем вам самые выгодные предложения на брендовые товары из Америки. Опираясь на свой многолетний опыт, выбираем только лучшие позиции из аутлетов и дискаунтеров, чтобы предоставить вам оптимальные цены, в которые не включены дополнительные расходы на аренду торговых помещений.

Доставка товаров осуществляется прямо с нашего склада до указанного вами адреса. Вы получаете оригинальный товар по цене, которая недоступна для местных магазинов. В нашем интернет-магазине вы всегда найдете широкий ассортимент брендовых товаров с выгодными скидками.

Мы следим за каждым этапом вашей покупки и предоставляем отслеживание заказа на всех этапах, начиная с момента оплаты.

  • Бренд Pololu
  • Доставка из Польши
  • Пункт выдачи СДЭК 7 июля
  • Стоимость доставки заказа в Россию от 710 ₽

Сроки доставки указаны ориентировочно и зависят от региона доставки. Подробнее на этой странице

Характеристики

Общие характеристики

Напряжение до
1.8 V
Напряжение от
1.5 V

Прочие свойства

Бренд
Pololu

Свойства

Каналы
1

Энергопитание

Сила тока
1.7 A

Описание

Description: PololuDRV8838 - single channel motor controller 11V/1.7A

The module based on theDRV8838allows to control one DC motor. The motor can be supplied with a voltage of up to 11 volts with a continuous current consumption of up to 1.7 A, and temporarily (for a few seconds) up to 1.8 A. We recommend that you readthe DRV8838's documentationbefore use.

Connection

Connect the motor supply voltage from 0 to 11 V to the VIN input. If the voltage is low (less than 1.5 V) it can be connected to the VMM output, this will bypass the reverse connection protection and compensate for the voltage drop. The power supply for the logical part from 1.8 V to 7.0 V is supplied to the VCC pin.

In a typical application, simply connect two control lines: PHASE direction selection and PWM speed control to the ENABLE pin. Both lines are internally pulled to ground by a resistor approximately 100 kΩ.

The SLEEP output enables the system to switch to low power mode. By default, the pin is pulled up to VCC via 10 kΩ, which means that the circuit is switched on. To switch to the Sleep mode, the low state must be specified.

PHASE ENABLE SLEEP OUT1 OUT2 Mode of operation 0 PWM 1 PWM L forward speed PWM %braking 1 PWM 1 L PWM Reverse speed PWM %braking X 0 1 L L

Stop,

outputs connected to ground

X X 0 Z Z free runningoutputs disconnected

1 - high state, 0 - low state

Exits PIN Description

VIN

Motor supply voltage from 0 V - 11 V with reverse connection protection. GND The weight of the module. VCC Supply voltage of the logical part from 1.8 V to 7 V. VM Motor supply voltage from 0 V - 11 V without reverse connection protection. OUT1 Outputs 1 to connect the motor outputs. OUT2 Outputs 2 to connect the motor outputs. PHASE Logical input defining the direction of engine rotation. Default is in low state. ENABLE Logical input for speed setting. A PWM signal must be connected to this output. Default is at low state. SLEEP Logical input that switches the system to the sleep state when low state is given. Default is high state.

Outputs are standardgoldpin strips, allowing the module to be plugged into thecontact boardor connected bywires.

Comparison of Polol controllers.

Polol specificationDRV8838
  • Number of channels: 1
  • Supply voltage: 0 V to 11 V
  • Operating voltage of the logical part: 1.8 V to 7.0 V
  • Continuous current per channel: 1.7 A
  • Maximum instantaneous current per channel: 1.8 A
  • PWM frequency: 250 kHz
  • Dimensions: 10.2 x 12.7 mm
  • Weight: 0.3 g (without connectors)
  • Included module and goldpin connectors
Useful links
  • Polol manufacturer's website #2990
  • Diagram of the DRV8838 module
  • DRV8838 system documentation

Доставка

Мы доставляем товары напрямую из Германии в Россию курьерской службой или в почтовое отделение. Вы можете выбрать подходящий для вас способ доставки при оформлении заказа. Стоимость доставки зависит от выбранного метода и начинается от 710 руб. Время доставки зависит от выбранного города и метода доставки, но в среднем занимает от 10 до 30 дней. Если вы оформите заказ прямо сейчас, мы доставим его в период с 26 июня - 16 июля.

На протяжении уже более 10 лет мы работаем с надежными и проверенными нами службами и предлагаем доставку электрики Pololu в различные города России, такие как  Москва, Санкт-Петербург, Новосибирск, Екатеринбург, Казань, Нижний Новгород, Челябинск, Самара, Уфа, Ростов, Омск, Красноярск, Воронеж и другие.

Вы всегда можете отследить свой заказ, используя номер посылки, сразу как только он будет отправлен к вам с нашего склада.